A Zippo is built to be refilled and repaired for life, and all of it takes about two minutes at a kitchen table. Our Hosts walk Guests through this at the counter every week, so here is the same walk-through in writing: how to refill a Zippo, how to change the flint when the wheel stops sparking, and how to trim or replace the wick when the flame gets weak. The parts cost a few dollars, and the flints, wicks and lighters ship anywhere we ship. You can also pick everything up at any of our El Paso stores.

What you need to refill a Zippo
- Zippo lighter fluid. It is naphtha, a thin, clean-burning fuel. Do not use butane, kerosene or charcoal lighter fluid. Our guide to what fuels a Zippo explains why.
- A flat surface and a paper towel. Fluid spills are the only real mess in this job.
- No open flame nearby. Fill it away from candles, stoves and anything lit.
How to refill a Zippo lighter, step by step
- Pull out the insert. Open the lid, grip the chimney (the metal guard with holes around the wick) and pull straight up. The whole inside slides out of the case.
- Flip it over and lift the felt pad. The bottom of the insert has a felt pad, usually stamped “LIFT TO FILL”. Lift one corner with a fingernail or a paper clip. You will see the cotton packing underneath.
- Wet the cotton slowly. Put the spout of the can against the cotton and squeeze gently. Go slowly and let the cotton drink. Stop when the fluid reaches the top of the cotton and it looks damp. If fluid pools or drips, you have gone a little too far.
- Put the insert back. Press the felt pad down, slide the insert into the case with the wheel on the hinge side, and push it all the way in.
- Wipe everything down. Wipe the lighter and your hands, and close the fluid can. Fluid on skin can cause irritation, which is the usual cause of “Zippo burn” on a leg after an overfilled lighter rides in a pocket.
- Wait a minute, then light it. Give the surface fluid a minute to evaporate. Then strike the wheel as normal.
Zippo Lighter Fluid 4oz$4.99 · View
Zippo Lighter Fluid 12oz$8.99 · View
How often does a Zippo need to be refilled?
About once a week with daily use, and every one to two weeks if you use it now and then. The fuel evaporates even when the lighter sits closed, so a Zippo left in a drawer for a month will be dry. That is normal and nothing is wrong with the lighter. If you carry one every day, topping it up on the same day each week keeps it from running out when you need it.
Why won’t my Zippo light after I refilled it?
Work through these in order. One of them fixes almost every Zippo that will not light.
| What you see | Likely cause | Fix |
|---|---|---|
| Sparks, but no flame | No fuel, or the fuel has not soaked up the wick yet | Refill, then wait a minute or two and try again |
| No sparks, wheel spins freely | Flint is worn out | Replace the flint (steps below) |
| Wheel is stuck or hard to turn | Flint is jammed or the wheel is clogged | Remove the flint, brush the wheel clean, fit a new flint |
| Weak, small or sooty flame | Wick tip is burnt and black | Pull up and trim the wick, or replace it (steps below) |
| Flame flares up and fluid leaks | Overfilled | Wipe it down and let it sit open for a few minutes |
How to replace a Zippo flint
The flint is the small stick that makes the spark. One flint lasts a few weeks of regular use. When the wheel spins with no spark, it is time for a new one.
- Pull the insert out of the case and turn it upside down.
- Unscrew the brass screw on the bottom with a coin or a small screwdriver. It is attached to a spring, so ease it out.
- Tap the insert on the table so the old flint falls out of the tube. If it is stuck, push it through gently with an unbent paper clip.
- Drop one new flint into the tube.
- Put the spring back in and tighten the screw until it sits flush.
A handy trick: a spare flint fits under the felt pad on the bottom of the insert, so you always have one with you.
Zippo Flints, 6 pack$2.99 · View
How to trim or replace a Zippo wick
The wick lasts a long time, but the tip slowly burns black and stops carrying fuel well. You can trim the same wick twice before it needs replacing.
To trim it: with the insert out of the case, grip the wick with needle-nose pliers and pull it up until clean, white wick shows above the chimney. Cut it level with the top of the chimney. Done.
To replace it:
- Remove the flint screw, spring and flint, then lift off the felt pad.
- Pull out all the cotton with tweezers and set it aside in order.
- Pull the old wick out, then thread the new wick down through the chimney from the top. Leave it level with the top of the chimney.
- Put the cotton back in small pieces, weaving the wick back and forth between the layers in an “S” shape so it touches as much cotton as possible.
- Refit the felt pad, flint, spring and screw, then refill the lighter.
Zippo Replacement Wick$1.99 · View
Looking for a new Zippo?
We keep more than 250 Zippo lighters in stock, from plain brushed chrome to licensed designs, and every one of them takes the same fluid, flints and wicks described above. Zippo lighters leave the factory empty, so add a can of fluid if it is a first Zippo or a gift.